NoSmoker Orion V3 battery mod with stainless steel atomizer ESS

 

The electronic cigarette Orion V3 from NoSmoker is equipped with an electronic, that incorporates a small 2-digit 7-segment display and a push-button to adjust several parameters by means of a menu structure and to show different measured values.

The adjustments and handling is intuitive by pressing the button short term or for a longer interval.

With the button actuated for more than 0.25 sec., power is applied to the heating winding, until the button is released or the maximum steam-time of about 19 second is exceeded (dependent on power, see chapter 2. Timing restrictions).

NoSmoker Orion V3 battery mod with stainless steel atomizer ESS

The electronic cigarette Orion V3 from NoSmoker is equipped with an electronic, that incorporates a small 2-digit 7-segment display and a push-button to adjust several parameters by means of a menu structure and to show different measured values.

The adjustments and handling is intuitive by pressing the button short term or for a longer interval.

With the button actuated for more than 0.25 sec., power is applied to the heating winding, until the button is released or the maximum steam-time of about 19 second is exceeded (dependent on power, see chapter 2. Timing restrictions).

orion v3Different from all other competitors, the Orion V3 works with a completely new technology enabling the device to handle high power in a very small volume. The power output is achieved by a true alternating current (+/- relative to housing or ground) and not with an adjusted voltage or a pulse width –modulated constant voltage.

Technically interested users please note: A measurement of the actual output power of the device requires a very fast rms-measuring device (root-mean-squarevalue or effective voltage measurement with a bandwidth of higher than 10MHz).

The selected power is – combined with the creation of the heater winding – decisive for the steaming result. With windings around 3 Ohms, i.e. quite a high number of windings, the vaporised volume is higher compared to less windings. The flash and the taste on the other hand are more effective and intense with a smaller volume but higher vaporising speed (higher temperature). On this aspect the user has to find his or her best configuration. We recommend to choose a mid-range power adjustment of 7W to 10W together with a winding resistance of 1.5 to 2.0 Ohms (based on 0.16mm Kanthal wire).

The Orion V3 is powered up by consecutive fast pressing of the button for 5 times. The LED display lights up and shows P1. With continued pressing of the button the user steps through the menu from P1 to P6 and the error menu E. When the actuation of the button is stopped, the current value of that specific menu is displayed after about 1 second for a duration of 2 seconds . The value can be changed by repeated pressing of the button or keeping the button pressed (auto repeat).

As soon as the display is off and the button is pressed for longer than 0.25 seconds, the heating winding is powered. 6 months warranty from receipt of purchase.

After receiving of your Orion V3, please clean the tank and the atomizer and in particularly all the holes. Wind, 3-4 coil turns, insert the batteries with the positive pole to the inside (opposite as in V2). The negative pole of the springs in the bottom cup, spring is not impressive, but it is a very good material and please do not replace the springs To turn on the Orion, please click 5 times. You then go to the position of E1, click and hold until 1 will be deleted. (you cannot delete the E1 if there is no coil) Go to the P5 position and set the Discharge Protection, for one battery is 2.8 – 3.5 volts,  for two battery is 5.6 – 7.0 volts. This is very important. In case of the settings, for example: 3.5 volt and 3.7 volt battery status, Orion may not work because the Discharge Protection is too high (standard is 3.3 volts, but set it to 2.8 volts). The next situation could be fatal using two battery and setting for one battery(severely discharged batteries).

PLEASE BE CAREFUL!!!

Next, if you want to experiment with the airflow, purchased 15G cannula needle (diameter 1.8 mm) and bend over the burner to the desired angle, the rest is easy. Orion will allow you to use very low resistance, eg 0.5 ohm delete the error do not go to P3.

— July 21, 2017

What Do You Think?